When learning the pre-release password, as well as the challenge and response sequence, the engine control module (ECM) is placed in learn mode. ĭTC P0633 : Theft Deterrent Key Not Programmed Or you'll waste your money buying parts your don't need. Your best bet, i say again, is have a professional technician sort it out. The components of the theft system are as follows: If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting. Both the ECM and TDM perform a calculation on this challenge. The ECM sends this challenge back to the TDM via the serial data circuit. When the ECM receives the TDM prerelease password, the ECM will challenge the password. If the transponders unique value is incorrect, the TDM will send the fuel disable password to the ECM. If the values match, the TDM will send the prerelease password via the serial data circuit to the ECM. The TDM then compares this value to a value stored in memory. The energized transponder transmits a signal that contains its unique value, which is received by the TDM. When an ignition key is inserted into the ignition lock cylinder and the ignition is switched ON, the transponder embedded in the head of the key is energized by the exciter coil surrounding the ignition lock cylinder. The immobilizer system functions are provided by the theft deterrent module (TDM) and the engine control module (ECM). The easiest way to check to see if this is all correct ,is by hooking up a scan tool an viewing data parameters. When this occurs, battery positive voltage is supplied through the switch side of the crank relay to the S terminal of the starter solenoid. If it is, the ECM then supplies 12 volts to the control circuit of the crank relay. The ECM verifies that the transmission is in Park or Neutral. The BCM then sends a message to the engine control module (ECM) notifying it that CRANK has been requested. When the ignition switch is placed in the Start position, a discrete 12-volt signal is supplied to the body control module (BCM) notifying it that the ignition is in the Start position. The TDM and ECM have now relearned the pre-release password and the challenge/response data. With a master vehicle key, turn the ignition to the RUN position for 15 seconds, then start the vehicle. Turn OFF the ignition and wait 2 minutes. The vehicle is now ready to relearn the key information and/or the passwords on the next ignition switch transition from OFF to CRANK. Observe the scan tool, after approximately 10 minutes the scan tool will display "Programming Successful, Turn OFF Ignition". On some vehicles the security indicator may be illuminated for the duration of the 10-minute relearn procedure.The remaining 10 minutes is the relearn timer. The first 2 minutes allow the scan tool to initialize the appropriate control module. The scan tool will initially display 12 Minutes.Vehicle Theft Deterrent Learn menu and choose the Vehicle Theft Deterrent Learn, ECM, or PK3 Replaced selection.Īt this point the scan tool must remain connected for the duration of the 10-minute relearn procedure. Ensure the correct programming selection is chosen based on component being replaced or programmed. On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions, using the Pass-Thru method. Turn ON the ignition, with the engine OFF.Įnsure that all power consuming devices are turned OFF on the vehicle. This 10-minute relearn procedure will relearn the prerelease password and the challenge/response data between the theft deterrent module (TDM) and the engine control module (ECM).Ĭonnect a scan tool to the vehicle in the pass-thru arrangement. You need a factory scan tool to do a reset key off an wait 2 min won't work on your vehicle. Hooking up a factory or some other professional type scan tool an checking code's in the anti-theft module an the ECM - engine control module. The padlock light lit, anti-theft system problem, more then likely. This is a computer problem, not the solenoid. Your best bet, have it towed to a qualified repair shop. Can it be the silinoted ? Solenoid is the correct spelling.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |